The effect of argon as atomization gas on the microstructure, machine hammer peening post-treatment, and corrosion behavior of twin wire arc sprayed (TWAS) ZnAl4 coatings

Simple item page
dc.contributor.authorTillmann, Wolfgang
dc.contributor.authorAbdulgader, Mohamed
dc.contributor.authorWirtz, Andreas
dc.contributor.authorMilz, Michael P.
dc.contributor.authorBiermann, Dirk
dc.contributor.authorWalther, Frank
dc.date.accessioned2022-01-21T12:09:06Z
dc.date.available2022-01-21T12:09:06Z
dc.date.issued2021-12-27
dc.description.abstractIn the twin wire arc spraying (TWAS) process, it is common to use compressed air as atomizing gas. Nitrogen or argon also are used to reduce oxidation and improve coating performance. The heat required to melt the feedstock material depends on the electrical conductivity of the wires used and the ionization energy of both the feedstock material and atomization gas. In the case of ZnAl4, no phase changes were recorded in the obtained coatings by using either compressed air or argon as atomization gas. This fact has led to the assumption that the melting behavior of ZnAl4 with its low melting and evaporating temperature is different from materials with a higher melting point, such as Fe and Ni, which also explains the unexpected compressive residual stresses in the as-sprayed conditions. The heavier atomization gas, argon, led to slightly higher compressive stresses and oxide content. Compressed air as atomization gas led to lower porosity, decreased surface roughness, and better corrosion resistance. In the case of argon, Al precipitated in the form of small particles. The post-treatment machine hammer peening (MHP) has induced horizontal cracks in compressed air sprayed coatings. These cracks were mainly initiated in the oxidized Al phase.en
dc.identifier.urihttp://hdl.handle.net/2003/40685
dc.identifier.urihttp://dx.doi.org/10.17877/DE290R-22543
dc.language.isoende
dc.relation.ispartofseriesCoatings;12(1)
dc.rights.urihttps://creativecommons.org/licenses/by/4.0/
dc.subjectTwin wire arc spraying processen
dc.subjectAtomization gasen
dc.subjectArgonen
dc.subjectZnAl4 coatingsen
dc.subjectOxidationen
dc.subjectMachine hammer peeningen
dc.subjectCorrosion behavioren
dc.subject.ddc620
dc.subject.ddc670
dc.subject.rswkThermisches Spritzende
dc.subject.rswkGaszerstäubungde
dc.subject.rswkArgonde
dc.subject.rswkAluminiumlegierungde
dc.subject.rswkZinkde
dc.subject.rswkOxidationde
dc.subject.rswkMaschinelles Oberflächenhämmernde
dc.subject.rswkKorrosionde
dc.subject.rswkBeschichtungde
dc.titleThe effect of argon as atomization gas on the microstructure, machine hammer peening post-treatment, and corrosion behavior of twin wire arc sprayed (TWAS) ZnAl4 coatingsen
dc.typeTextde
dc.type.publicationtypearticlede
dcterms.accessRightsopen access
eldorado.secondarypublicationtruede
eldorado.secondarypublication.primarycitationTillmann, W.; Abdulgader, M.; Wirtz, A.; Milz, M.P.; Biermann, D.; Walther, F. The Effect of Argon as Atomization Gas on the Microstructure, Machine Hammer Peening Post-Treatment, and Corrosion Behavior of Twin Wire Arc Sprayed (TWAS) ZnAl4 Coatings. Coatings 2022, 12, 32. https://doi.org/10.3390/coatings12010032de
eldorado.secondarypublication.primaryidentifierhttps://doi.org/10.3390/coatings12010032de

Files

Original bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
coatings-12-00032-v2.pdf
Size:
10.24 MB
Format:
Adobe Portable Document Format
Description:
Download
License bundle
Now showing 1 - 1 of 1
No Thumbnail Available
Name:
license.txt
Size:
4.85 KB
Format:
Item-specific license agreed upon to submission
Description:
Download

Collections

Lehrstuhl für Werkstofftechnologie